RFM12 FSK - Revision history

GooPie4o: /* Configuration */

2013-06-04T10:48:03Z

‎Configuration

2013-03-12T07:13:43Z

2013-03-06T09:26:22Z

‎Connection

2013-03-06T09:25:35Z

2013-03-06T09:22:59Z

2013-03-06T09:21:27Z

2013-03-06T09:20:57Z

2013-03-06T08:54:10Z

2013-03-06T08:53:09Z

2012-12-29T09:59:26Z

← Older revision		Revision as of 10:48, 4 June 2013
Line 38:		Line 38:
	== Configuration ==		== Configuration ==

		+	\| \| Network ---> \| \|
		+	...
		+	\| \| [*] IP over RFM12 (FSK transmitter) support ---> \| \|
		+	...
		+	\| \| (0) RFM12 select \| \|
		+	\| \| (433.920MHz) RFM12 frequency \| \|
		+	\| \| [ ] Use slow SPI \| \|
		+	\| \| [ ] Use RFM12B \| \|
		+	\| \| (19200) RFM12 Baudrate \| \|
		+	\| \| IP address: "192.168.5.1" \| \|
		+	\| \| Netmask: "255.255.255.0" \| \|
		+	\| \| [ ] Source Route ALL packets \| \|
		+	\| \| [ ] RFM12 Packet Forwarding \| \|
		+	\| \| [-] RFM12 ARP-Proxy \| \|

	[[Category:RFM12]]		[[Category:RFM12]]

@@ Line 34: / Line 34: @@
 If more than one RFM12 are used with Ethersex, the number in SPI_CS_RFM12_0 defines the number of the module.
-Each needs its own pinning. The RFM12_USE_INT defines whether nRQ is connected to INT0, INT1 or INT2 of the ATmega.
+Each needs its own pinning. The RFM12_USE_INT defines whether nRQ is connected to INT0, INT1 or INT2 of the AVR.
 == Configuration ==

@@ Line 33: / Line 33: @@
    RFM12_USE_INT(2)
-If more than one RFM12 are used with Ethersex, the number in SPI_CS_RFM12_0 defines which number of your module.
+If more than one RFM12 are used with Ethersex, the number in SPI_CS_RFM12_0 defines the number of the module.
 Each needs its own pinning. The RFM12_USE_INT defines whether nRQ is connected to INT0, INT1 or INT2 of the ATmega.
 == Configuration ==

@@ Line 25: / Line 25: @@
    /* port the rfm12 module CS is attached to */
-   pin(SPI_CS_RFM12, PB0, OUTPUT)
+   pin(SPI_CS_RFM12_0, PB0, OUTPUT)
-   /* port the LEDS for rfm12 txrx attached to */
+   /* port the LEDS for rfm12 tx/rx attached to */
    pin(STATUSLED_RFM12_TX, PB3, OUTPUT)
    pin(STATUSLED_RFM12_RX, PB1, OUTPUT)
@@ Line 33: / Line 33: @@
    RFM12_USE_INT(2)
-The RFM12_USE_INT defines whether nRQ is connected to INT0, INT1 or INT2 of the ATmega.
+If more than one RFM12 are used with Ethersex, the number in SPI_CS_RFM12_0 defines which number of your module.
 == Configuration ==

← Older revision		Revision as of 09:22, 6 March 2013
Line 34:		Line 34:

	The RFM12_USE_INT defines whether nRQ is connected to INT0, INT1 or INT2 of the ATmega.		The RFM12_USE_INT defines whether nRQ is connected to INT0, INT1 or INT2 of the ATmega.
		+
		+	== Configuration ==
		+

	[[Category:RFM12]]		[[Category:RFM12]]

@@ Line 11: / Line 11: @@
 |CODE=[https://github.com/ethersex/ethersex/tree/master/hardware/radio/rfm12 https://github.com/ethersex/ethersex/tree/master/hardware/radio/rfm12]
 }}
 == Connection ==
-[[Image:Rfm12 connection.png]]
+If you are using hardware SPI, which is the default, connect the RFM12 to the AVR as follows:
 [[Category:RFM12]]

← Older revision		Revision as of 09:59, 29 December 2012
Line 11:		Line 11:
	\|CODE=[https://github.com/ethersex/ethersex/tree/master/hardware/radio/rfm12 https://github.com/ethersex/ethersex/tree/master/hardware/radio/rfm12]		\|CODE=[https://github.com/ethersex/ethersex/tree/master/hardware/radio/rfm12 https://github.com/ethersex/ethersex/tree/master/hardware/radio/rfm12]
	}}		}}
		+
		+	[[Category:RFM12]]